©2006 Avery Dennison Corp. All rights reserved. 28028 28028 0 0 TC9416CTIUM Rev. AF 1/10User Manual® Monarch 9416 XL, 9825Printers Intelligent K
1-6 User Manual Using the Keyboard The keyboard has full alphabetic keys with 10 numeric keys, five function keys, four arrow keys, and several speci
Introduction 1-7 Control Keys Escape. Returns the display to the previous menu. Also clears an error. Clear. Clears the entire field. Pause. St
1-8 User Manual
Setting Up the Printer 2-1 SETTING UP THE PRINTER You must configure the printer before printing formats. The most common configuration options are
2-2 User Manual 5. Press Enter. You see COMM 1 Baud Rate 6. Press Enter. You see BAUD RATE
Setting Up the Printer 2-3 Selecting the Format Sending Mode There are two Format Sending Modes: As Needed and Always. To send all formats at once,
2-4 User Manual 1. From the Config Menu, press or until you see 2. Set Separators 2. Press Enter. You see Set Batch Separators 1=Enabled, 2=D
Setting Up the Printer 2-5 Setting the Print Mode There are two print modes: continuous (no peel) and on-demand (peel). Continuous mode prints label
2-6 User Manual Setting the Ribbon Thermal direct supply does not require a ribbon. Thermal Transfer supply does require a ribbon. 1. From the Conf
Setting Up the Printer 2-7 Printing a Test Label The test label shows the printer settings. Refer to your Equipment Manual for more information. 1.
Each product and program carries a respective written warranty, the only warranty on which the customer can rely. Avery Dennison Corp. reserves the
2-8 User Manual Setting the Print Contrast The print contrast controls the darkness of the printing on your supply. The range is –699 to +699 and th
Setting Up the Printer 2-9 Setting the Print Position This function adjusts where data prints vertically on the supply. Adjust the print if it is to
2-10 User Manual Setting the Supply Position This function adjusts the printer to print at the vertical 0,0 point on the supply. Note: The supply
Setting Up the Printer 2-11 Resetting the Configuration To change all configurations back to the default settings: 1. From the Main Menu, press . Y
2-12 User Manual
Printing Labels 3-1 PRINTING LABELS This chapter describes the data entry procedures for each format. Your keyboard may contain custom formats that
3-2 User Manual Format 1 1. Load 1.2” width x 1.1” length supply. 2. Enter the data as prompted: Prompt What You Do LINE 1 Enter up to ten charac
Printing Labels 3-3 Format 3 1. Load 1.2” width x 1.1” length supply. 2. Enter the data as prompted: Prompt What You Do LINE 1 Enter up to 12 cha
3-4 User Manual Format 4 1. Load 1.5” width x 2.7” length supply. 2. Enter the data as prompted: Prompt What You Do LINE 1 Enter up to 15 charact
Printing Labels 3-5 Format 5 1. Load 1.5” width x 2.7” length supply. 2. Enter the data as prompted: Prompt What You Do LINE 1 Enter up to 15 cha
i TABLE OF CONTENTS INTRODUCTION ...1-1 Audience ...
3-6 User Manual
Troubleshooting 4-1 TROUBLESHOOTING Use this chapter to correct some problems that may occur. Problem Action The keyboard display is blank. Make su
4-2 User Manual
28028 28028 0 0 Avery Dennison Printer Systems Division170 Monarch LaneMiamisburg, OH 453421-800-543-6650 (In the U.S.A.)1-800-387-4740 (In Canada)w
ii Resetting the Configuration ...2-11 PRINTING LABELS...
Introduction 1-1 INTRODUCTION The Monarch® Intelligent and Industrial Kits allow you to print bar code labels offline using the Monarch® 9416®, 9416®
1-2 User Manual Using This Manual Following is a summary of the contents of this manual. Chapter Contents 1 Introduction Explains how to connect t
Introduction 1-3 Connecting the 939I to a 9416 Printer 1. Turn OFF the printer before you connect the keyboard's cable. 2. Plug the 9-pin coil
1-4 User Manual Auxiliary Power Supply Connecting the 939I with a Script to a 9800® Printer When using the keyboard with a script and a 9825, 9855, o
Introduction 1-5 Connecting the 939I in Terminal Mode to a 9855/9860 Printer When using the keyboard in terminal mode (no script) with a 9855 or 9860
Commentaires sur ces manuels